Should I use flexible grout?

A flexible grout called QuartzLock 2 was our best solution. … The advantage of this type of grout is when it dries, it becomes flexible, and if there is any movement in the floor, the grout flexibility dissipates the stress that would otherwise put pressure on the tile.

How do you mix flexible grout?

How long does flexible grout take to dry?

Allow approximately 15 minutes for the grout to dry sufficiently before cleaning off diagonally across the grout lines with a damp sponge.

What is flexible tile?

Flexible tiles are made up of elastic materials providing the flexibility as compared to regular tiles, which are constructed by using merely minerals. … Vinyl, plastic and rubber floor tiles are commonly available types of flexible tile in the flooring market.

Why did my grout harden in the bucket?

The hotter the air temperature, the grout powder and the water, the less time you have to install it once it’s mixed. … As you do this tedious work, the mixed grout can harden in the bucket. This is why you don’t want to mix too much grout up until you discover how fast you can use it up.

How many mm of grout do you need between tiles?

Ideally, your grout joints would be 1-3mm. Often we see 1mm grout joints between wall tiles and 3mm grout joints between floor tiles. Not only does it look better to have smaller joints, it also can minimise issues. For example, grout will discolour over time so keeping the joints smaller will minimse this issue.

Is porcelain tile flexible?

Do you mix grout with hot or cold water?

Use cool water to mix grout powder; never use hot or warm water. Keep ice on hand to cool down the water. Keep the grout bags and mixing container cool. ◗ Do not mix the grout with excessive amounts of water or remix with additional water.

Can hardened grout be reused?

No. Grout is basically a form of concrete. If this technology existed then when the government needed to redo roads they would just add this magical potion and road would be redone. A small batch of grout mixed properly only has a usable time of a few hours.

How long will grout stay workable?

Grout hardens completely after 30 to 60 minutes. If you wait too long after slaking, it’s possible that you’ll have to dispose of the batch and start again. Adding water does not reactivate grout at this point. Repeat as needed to make enough batches of grout to complete your project.

Can you remix grout?

Let the grout slake

Remix the grout after letting it set for 10 or 15 minutes. Add a little water if the grout is too thick. … Remix the grout after the slaking period and adjust the mixture by adding a little more powder or water until you reach the viscosity of mayonnaise.

Can I use thinset as grout?

Thinset mortar, commonly used for securing stone to a surface becomes very hard just as a Portland cement grout becomes as it dries. Although the intended use for thinset is not for mortar joints. You can use it on backsplashes and other surfaces that will not see heavy traffic.

Can you grout over grout?

ANSWER. ANSWER – It is possible to grout over existing grout if there is enough depth to do so. 1/8 inch depth may or may not be adequate depending on the type of grout used. A latex modified grout may work, but you have to properly clean the existing grout to ensure the new grout adequately bonds.

Can grout be softened?

Water-based tile grout used in bathroom areas like showers is designed to harden and become impenetrable. … When it does, you need to soften the tile grout and remove it so you can install new grout. Set your heat gun at 300 degrees Fahrenheit or less. If you use a blow dryer, place it on the lowest setting.

Can you mix grout with water?

Add water to grouting powder in the manufacturer-recommend ratio. … Adjust grout consistency by adding more powder or water. Let grout rest (slake) for up to 10 minutes. Use a grout knife to mix thoroughly once more.

Can you mix grout with a drill?

How do you soften grout?

Will vinegar soften grout?

Vinegar is an acid and tends to accelerate the grout breakdown, dissolving the grout, and leaving it in a deteriorated state. It also contains acetic acid which gradually dissolves the protective sealer by changing its pH. However, when used carefully white vinegar can be used to clean the grout as discussed below.

What will loosen grout?

What is epoxy grout?

Traditional grout is made from a cement based mix. … Epoxy grout on the other hand, is made of epoxy resins combined with a filler powder. This makes it waterproof and almost completely resistant to stains. It’s durability makes it the ideal choice for splashbacks, floors and high-traffic areas.

Do you have to remove old grout to Regrout?

You don’t need to remove all the grout, or even most of it, but removing the dirty grout on the surface gives the new grout something to which to bond. … Removing much of the grout isn’t necessary; just get it down enough from the surface to allow new grout to bond. Vacuum up any loose dust and particles.

Can you caulk over grout?

Generally speaking, caulking over grout is not a great idea. … However, if you’re attempting to replace the grout connecting the bathtub to the floor, or filling the space between two tiles or stones, your best chance is to re-grout it.

Is epoxy grout flexible?

Epoxy is flexible: Epoxy isn’t rigid or gritty like regular grout. In fact, when it comes to the epoxy grout vs. regular grout debate, epoxy is always noted for its elasticity and durability. … Epoxy is not absorbent: Epoxy grouts are highly water resistant.

Is epoxy grout necessary?

Because epoxy can discolor porous surfaces, such as unglazed quarry tiles or limestone, these should be sealed before grouting. But its stain resistance, hardness, and durability make epoxy grout the best choice for showers, kitchen counters, backsplashes, floors, and other heavy-traffic areas.

What is the difference between acrylic grout and epoxy grout?

Acrylic grouting is smooth /sanded surface and slightly gloss looking. Epoxy grouting is rough surface with matte finishing. It’s the replacement of existing grout lines with sanded epoxy grout that is traditionally used in swimming pool grouting and therefore the toughest available product on the market.